Bank, Loose, and Compacted Yardage on Civil Sites
When crews ask how much dirt do I need for a cut or backfill, soil volume shifts across three states: Bank Measure (undisturbed native ground), Loose Measure (excavated soil in a truck bed, swelling 15% to 25%), and Compacted Measure (mechanically tamped fill). Suppliers deliver loose yards. Placed in a utility trench, retaining wall backfill, or building pad toward 95% Standard Proctor density (ASTM D698), loose dirt shrinks 10% to 15%. Use this fill dirt calculator and topsoil calculator before dispatch: compact granular fill dirt and sandy loam with a vibratory plate compactor, and tamp cohesive heavy wet clay with a jumping-jack rammer in 4-to-6 inch lifts.
Soil Density Profiles & Haulage Tonnage Reference
State DOT axle laws cap tri-axle dump trucks around 18 to 22 tons of net payload depending on truck tare weight, not box volume alone. Converting cubic yards to dirt weight in tons with this dirt volume calculator and excavation calculator prevents overloaded trucks and short loads.
| Soil Type | lbs / yd³ | Tons / yd³ | Tri-Axle (yd³) | Site Application |
|---|---|---|---|---|
| Clean Fill Dirt | 2,000–2,150 | 1.05 Tons | 14–15 yds | Building pads, wall backfill, grading |
| Screened Topsoil | 2,100–2,300 | 1.10 Tons | 13–14 yds | Lawn top-dressing, sod, garden beds |
| Heavy Wet Clay | 2,600–2,900 | 1.35 Tons | 11–12 yds | Pond liners, clay caps, berms |
| Sandy Loam | 2,400–2,600 | 1.25 Tons | 12–13 yds | Paver sub-base, drain fields |
How to Calculate Dirt Volume: Field Measurement Protocol
Run this dirt yardage calculator manually in four steps from site tape measurements.
Measure rectangular pads in feet and multiply length by width. For circular pits or mounds, divide diameter by 2 for radius and multiply pi (3.1416) by radius squared.
Divide depth in inches by 12. A 4-inch top-dress is 0.333 ft, a 6-inch pad cut is 0.50 ft, and an 18-inch utility or drainage trench is 1.50 ft.
Multiply area (sq ft) by depth (ft) for cubic feet, then divide by 27. A 30 by 20 foot cut at 6 inches equals 300 cu ft, or 11.11 cubic yards.
Multiply raw yardage by 1.10 for 10% tamping or 1.15 for deep trench backfill, then multiply by soil density (tons/yd³) to size dump truck deliveries.
Haulage Logistics: Dump Truck Types and Delivery Limits
Half-ton pickups hold about 1.5 cubic yards max volume (near 0.75 tons payload). Larger orders use three dump truck classes:
- Single-Axle Dump Truck: 5 to 6 cubic yards (about 6 tons net) for tight residential driveways and low overhead lines.
- Tandem / Tri-Axle Dump Truck: 12 to 15 cubic yards (up to 18 to 22 tons net payload per tare weight and state axle rules) for pads and backfill.
- End-Dump Semi Trailer: 22 to 26 cubic yards (25 to 28 tons net), requiring wide turning radii, firm level ground, and clear overhead airspace.
Field & Excavation Safety Notice
- Call 811 Before Digging: Request utility locates 48 to 72 hours ahead to mark gas, electric, water, and fiber lines.
- OSHA 29 CFR 1926 Subpart P: Excavations 5 feet or deeper require sloping, benching, or shoring (unless stable rock per a competent person), with egress ladders within 25 feet at 4 feet or deeper.
- Net Payload & Scale Tickets: Capacities reflect estimated net payload rather than gross vehicle weight (GVW). Verify final tonnage on supplier scale tickets because moisture alters soil weight.
- Geotechnical Testing: Verify ASTM D698 / D1557 Proctor density on load-bearing pads, retaining walls, and inspected fills.
Frequently Asked Questions About Dirt Yardage & Excavation
How many cubic yards of dirt are in a dump truck? ↓
A standard tri-axle dump truck hauls about 12 to 15 cubic yards of dirt, depending on state DOT axle laws that typically cap net payload near 18 to 22 tons after tare weight. Single-axle trucks carry about 5 to 6 cubic yards (5 to 7 tons).
How much does one cubic yard of dirt weigh? ↓
Dry clean fill dirt weighs about 2,000 to 2,150 lbs (1.00 to 1.08 tons) per cubic yard. Screened topsoil averages 2,200 lbs (1.10 tons), sandy loam averages 2,500 lbs (1.25 tons), and heavy wet clay runs 2,700 to 3,000 lbs (1.35 to 1.50 tons).
Why do I need to add a dirt compaction factor when ordering? ↓
Loose hauled soil contains air voids. When placed in 4-to-6 inch lifts and tamped with a plate compactor on granular soil or a jumping-jack rammer on clay toward 95% Standard Proctor density (ASTM D698), volume shrinks 10% to 15%.
How do I calculate dirt for a raised garden bed or circular fire pit? ↓
Knowing how to calculate dirt for a raised garden bed means multiplying length by width by depth in feet and dividing by 27. For circular beds or fire pits, square the radius, multiply by pi (3.1416) and depth in feet, then divide by 27.
What is the difference between fill dirt and screened topsoil? ↓
Clean fill dirt is inorganic mineral subsoil free of roots and debris, suited for structural subgrades, retaining wall backfill, and building pads because it will not rot. Screened topsoil holds organic humus for sod and garden beds and should not go under structural concrete.