BlueprintCalcs 2D Parametric Trade Tools

Wheel Offset Calculator

To calculate wheel offset and poke, compare current and new rim widths and ET offsets. Inner clearance delta equals half the width change plus offset change: (ΔWidth ÷ 2) + ΔET. Outer poke equals half the width change minus offset change: (ΔWidth ÷ 2) − ΔET.

2D CAD Blueprint
⚠ Aggressive Fitment
SUSPENSION STRUT FENDER LIP HUB MOUNTING FACE Current: 8" ET+45 WHEEL CENTERLINE +35 BS: 6.63" Poke: 3.87" INNER STRUT CLEARANCE DELTA: +9mm Closer OUTER FENDER POKE DELTA: +29.1mm Outward FITMENT STANCE: Aggressive Stance
● Calculated with 1.0" flange lip allowance (0.5" per bead seat).
Positive ET = Tucked Inward | Low/Negative ET = Pokes Out

Wheel Specifications

SAE J2530 Standard
Fitment Preset (Auto-Fill) SAE J2530
CURRENT (OEM) SETUP
NEW (PROPOSED) SETUP
FENDER POKE +29.1 mm Outward Flush
STRUT CLEARANCE -9 mm Inner Gap Delta
BACKSPACING 6.63" Hub to Inner Lip
FITMENT Aggressive Stance Clearance Tier
⚠ Aggressive Stance: Fender roll or negative camber likely required to prevent tire rubbing on compression.
Fitment Takeoff & Geometry Aggressive Stance
Inner Strut Delta:
9 mm LESS clearance inside (closer to strut)
Outer Fender Poke:
29.1 mm MORE poke outward (closer to fender lip)
Current Backspacing:
6.27" (2.73" Poke)
New Backspacing:
6.63" (3.87" Poke)
Scrub Radius Delta:
Shifts scrub radius +10 mm positive (increased steering kickback over bumps, sharper turn-in feel).

Wheel Offset ET, Backspacing & Suspension Geometry Explained

Upgrading wheels and tires is one of the most impactful mechanical modifications for vehicle track stance, lateral cornering grip, and aesthetic proportion. However, selecting aftermarket wheels without precise coordinate calculation often results in catastrophic tire sidewall rubbing against MacPherson suspension strut bodies, inner fender liner shredding, or body panel fender lip gouging during heavy suspension compression.

The two foundational measurements governing wheel fitment are Offset (ET) and Backspacing. While enthusiasts frequently conflate them, they operate on different coordinate planes:

  • Offset ET (Einpresstiefe): The distance measured in millimeters from the wheel's true lateral centerline to the hub mounting face. If the mounting face is outboard of the centerline (toward the street), the offset is positive (+ET). If the face is inboard of the centerline (deep into the barrel), the offset is negative (-ET).
  • Backspacing: The distance in inches from the hub mounting pad to the extreme inboard edge of the rim flange. Backspacing accounts for the extra 0.5 inches of structural lip required to retain the tire bead.

Common Wheel Width & Offset Conversions Table

Rim Width Overall Width (+1") Offset ET Backspacing Frontspacing (Poke) Fitment Type
8.0 Inches 9.0 Inches +45 mm 6.27 Inches 2.73 Inches OEM Factory Standard
8.5 Inches 9.5 Inches +38 mm 6.25 Inches 3.25 Inches OEM+ Flush Alignment
9.5 Inches 10.5 Inches +35 mm 6.63 Inches 3.87 Inches Aggressive Flush Fitment
10.0 Inches 11.0 Inches +20 mm 6.29 Inches 4.71 Inches Widebody / Fender Roll Required

The Impact of Offset on Scrub Radius & Steering Feedback

Changing offset does not merely affect wheel well clearances; it fundamentally alters the vehicle's kingpin steering geometry. The imaginary line passing through the upper and lower ball joints (or strut mount bearing to lower ball joint) is projected downward onto the asphalt. The distance between where this steering axis strikes the ground and the center of the tire contact patch is the Scrub Radius.

When you lower the offset (e.g., from +45mm to +30mm) or add 15mm bolt-on spacers, you move the tire contact patch outboard while the steering axis pivot remains stationary. This shifts the scrub radius in the positive direction:

  • Increased Turn-In Sharpness: Initial turn-in response feels more direct and responsive.
  • Increased Kickback & Tramlining: Road surface imperfections, bridge expansion joints, and rutted asphalt exert greater torque around the steering axis, pulling the steering wheel in the driver's hands.
  • Accelerated Hub Bearing Wear: Moving the load line further outward increases the cantilever bending moment applied to wheel hub bearings and suspension control arm bushings.

Frequently Asked Questions: Wheel Fitment, Spacers & Offsets

What is wheel offset and what does ET stand for? ↓

Wheel offset (abbreviated as ET from the German word Einpresstiefe, meaning press-in depth) is the millimeter distance between the true wheel centerline and the flat hub mounting surface where the wheel meets the brake rotor. A positive offset pushes the mounting pad toward the outer street face, pulling the wheel inward under the vehicle. A negative offset pushes the mounting pad deep inside the barrel, poking the wheel outward.

How do you convert wheel offset ET to backspacing? ↓

Backspacing is measured from the hub mounting pad to the extreme back lip of the rim barrel. Because rim lip bead flanges add roughly 0.5 inches per side (1.0 inch total overall width), the formula is: Backspacing (inches) = (Rim Width + 1.0) ÷ 2 + (Offset ET ÷ 25.4).

What happens if I change my wheel offset by 10mm? ↓

Reducing offset from +45mm to +35mm pushes the entire wheel assembly 10mm outward toward the fender. This widens the vehicle track width by 20mm total, enhancing cornering grip and aesthetics, but also increases positive scrub radius and leverage on wheel bearings and ball joints.

Will a 9.5-inch wide wheel fit if my car came with 8.0-inch wheels? ↓

A 1.5-inch wider rim adds 38.1mm of total width (19.05mm inward toward the strut and 19.05mm outward toward the fender). If offset remains identical, you lose 19mm of strut clearance. However, dropping the offset by 10mm (e.g. from ET45 to ET35) shifts the wheel outward, resulting in only 9mm loss of inner clearance and 29mm of outward fender poke.

What is scrub radius and how does offset affect steering? ↓

Scrub radius is the distance at the ground between the steering axis inclination (SAI) kingpin projection and the center of the tire contact patch. Decreasing wheel offset increases positive scrub radius, which provides more tactile steering feedback but can induce tramlining (following road ruts) and torque steer under heavy acceleration.

Can wheel spacers fix an offset that is too high? ↓

Yes. Installing a 10mm hubcentric wheel spacer effectively reduces a wheel offset from +45mm to +35mm, moving the wheel 10mm outward and restoring inner strut clearance. Always ensure at least 6.5 to 8 full turns of thread engagement on extended wheel studs or lug bolts.

Workshop & CAD Calculators

Related Layout Tools

View Full Workshop & Automotive CAD Hub 12 Tools →