Gravity Walls vs. Geogrid Reinforcement
A segmental retaining wall built with dry-stacked ASTM C1372 blocks resists lateral soil pressure while flexing slightly with freeze-thaw cycles.
- Unreinforced Gravity Walls (< 4.0 ft Total Height): Dead block weight, rear interlock, and a 3/4-inch per foot setback batter resist tipping on flat, stable soil (check local 3-foot permit thresholds).
- Geosynthetic Reinforced Walls (4.0 ft+ or Surcharged): At 4.0 ft total height or under a sloped hillside or driveway surcharge load, uniaxial geogrid ties between courses and extends back at least 60% of total height.
Block Sizes, Face Areas, and Weights
| Block Class | Size (H × W × D) | Face Area | Unit Weight | Unreinforced Limit | Typical Use |
|---|---|---|---|---|---|
| Commercial 8x18 | 8" × 18" × 12" | 1.00 sq ft | 75 - 80 lbs | 3.5 - 4.0 ft unreinforced; >=4.0 ft requires PE geogrid | Commercial cuts, terraced grades (with PE geogrid) |
| Landscape 6x16 | 6" × 16" × 10" | 0.67 sq ft | 30 - 35 lbs | 3.5 - 4.0 ft max (flat crest) | Patio terraces, yard grading, steps |
| Garden 4x12 | 4" × 12" × 8" | 0.33 sq ft | 16 - 20 lbs | 2.0 - 2.5 ft max | Low borders, flower beds, tree rings |
NCMA Embedment Depth, Leveling Pad, and Drainage
Saturated backfill weighs over 85 lbs/ft³ (vs. 35 lbs/ft³ dry), so every wall needs frost-safe embedment and drainage to relieve hydrostatic pressure:
- Embedment Depth: Bury 1 inch per foot of wall height, minimum 6 inches or 1 full buried course (12 inches on sloped front toes).
- 6-Inch Leveling Pad: Tamp crusher run aggregate 12 inches wider than the block depth in compacted lifts to 95% Proctor density, and set starter blocks level.
- 12-Inch Drainage Gravel & Filter Fabric: Place washed #57 drainage gravel behind blocks over a 4-inch perforated drain pipe sloped 1% to daylight, wrapped in non-woven filter fabric, and glue cap stones with masonry adhesive.
How to Calculate Retaining Wall Blocks & Gravel: 5 Steps
Measure linear feet along the wall face and exposed height from finished front grade to the top course (e.g., 30 ft long by 3.5 ft exposed).
Apply NCMA embedment depth: 1 inch buried per foot of wall height, minimum 6 inches or 1 full buried course (3.5 ft exposed on 6x16 blocks = 8 total courses).
Divide length by block width in feet (30 / 1.333 = 23 blocks/row), multiply by 8 courses (184 blocks), and add 5% waste for cuts (194 blocks).
Divide length by 16-inch cap width with 5% waste (25 cap stones) and add 1 tube of polyurethane masonry adhesive per 15 linear feet (2 tubes).
Calculate trench cubic yards (L x W x 0.5 ft / 27) plus 15% compaction for crusher run (1.82 tons), and size a 12-inch drainage gravel chimney at 1.35 tons/yd³ (5.51 tons).
Engineering, Permit & Excavation Notice
- Permits & PE Design: Walls 4 ft or taller in total height including the buried course (3 ft in stricter cities), or walls supporting slopes, driveways, parking pads, pools, or building footings require permits, PE-stamped plans, and engineered geogrid.
- Call 811 Before You Dig: Request public utility locates 48 to 72 hours ahead, and hand-pot near irrigation, pool, lighting, or septic lines.
- Soil & Inspector Check: Verify soil bearing capacity, frost depth, and drain daylighting with your local building inspector or geotechnical engineer.