BlueprintCalcs 2D Parametric Trade Tools

Crushed Stone Calculator

To calculate crushed stone, multiply length by width by depth in feet and divide by 27 for cubic yards. Add an 8% to 15% compaction allowance. Multiply total yards by 1.35 for #57 clean stone or 1.50 for crusher run to estimate delivery tonnage.

CRUSHED STONE TRENCH & BEDDING CAD
Ref: ASTM C33 / AASHTO M43 #57
DETAIL A: AGGREGATE & SUB-BASE 3.5X Compact Subgrade (Verify Soft Spots) Non-Woven Geotextile Fabric (Class 1) Interlocked Lift Finished Base Crown (2% Slope) *Ref: Crushed angular stone locks better than pea gravel; compact base in 4" lifts. Grade: 0.00' Subgrade Base Finished Base Surface A Width: 10' 0" Depth: 4" QUARRY WEIGHT & HAULAGE TAKEOFF 1 Tri-Axle Loads (5.40 Tons) 4 yd³ | 1 Single-Axle Loads
Total Stone: 5.4 Tons (4 Cu Yds) | Compaction Allowance: +0.3 yd³ (@ 8%) Gradation: #57 Clean Crushed Stone (3/4" - 1") (2700 lbs/yd³)

Aggregate Parameters

ASTM C33 Ref
Quick Presets:
Footprint Shape
30' 0"
10' 0"
4" Thickness
Stone Gradation (ASTM C33 / DOT Base)
8% Allowance
Crushed Stone Delivery Takeoff ASTM C33 #57
Total Quarry Delivery Weight: 5.40 Tons
Total Volume (with compaction): 4.00 Cu Yds
Net Volume: 3.7 yd³ Compaction Loss: +0.3 yd³
TRI-AXLE TRUCKS (~18.5T) 1 Loads
50-LB RETAIL BAGS 216 Bags

Clean #57 Aggregate vs. Dense-Graded Base (Crusher Run)

Quarries process crushed limestone, granite, or trap rock to ASTM C33 and ASTM D2940 specs. Washed #57 clean aggregate (3/16" #4 sieve to 1") leaves roughly 40% void space for French drains and pipe bedding. Unlike a basic gravel calculator, sub-base sizing separates drainage rock from structural courses.

Crusher run (dense graded aggregate, DGA, or 21A) mixes 3/4-inch rock down to fine stone dust. Placed in 4-inch lifts, moistened, and rolled, those fines lock into a firm driveway base or paver sub-base.

Gradation Bulk Density & Compaction Factor Table

Quarry scales bill by net ton, so crews convert cubic yards using bulk density, tons per cubic yard, and a gradation compaction factor:

Gradation Sieve Size Bulk Density Tons / Cu Yd Compaction Primary Site Use
#57 Clean 3/16" (#4) to 1" 2,700 lbs/yd³ 1.35 Tons 5% - 8% French drains, pipe bedding
Crusher Run / DGA 3/4" to Dust 3,000 lbs/yd³ 1.50 Tons 12% - 15% Driveway base, paver sub-base
#411 Base Aggregate 1/2" to Dust 2,900 lbs/yd³ 1.45 Tons 10% - 15% Shed pads, shoulder fill
#4 Ballast Stone 1.5" to 2.5" 2,600 lbs/yd³ 1.30 Tons 3% - 5% Tracking pads, wet subgrade
Stone Dust / Screenings 3/8" to Powder 2,800 lbs/yd³ 1.40 Tons 15% - 20% Flagstone joints, walkways

How to Calculate Crushed Stone Tonnage: Contractor Protocol

Step 1: Measure Base Footprint

Multiply length by width in feet for rectangular pads. For circular fire pits, divide diameter by 2 for radius and compute pi x r^2.

Step 2: Convert Depth to Feet

Divide depth in inches by 12: 3 inches equals 0.25 ft, 4 inches equals 0.333 ft, and 6 inches equals 0.50 ft.

Step 3: Compute Cubic Yards

Multiply area (sq ft) by depth (ft) and divide by 27. A 50 by 10 foot drive at 4 inches equals 6.17 cubic yards.

Step 4: Add Compaction Allowance

Add 5% to 8% settling for #57 clean stone, or 12% to 15% compaction for crusher run (DGA) with stone dust fines.

Step 5: Convert Yards to Tonnage

Multiply total yards by bulk density (1.35 tons/yd3 for #57; 1.50 tons/yd3 for crusher run) to book tri-axle dump truck deliveries.

Haulage Logistics: Legal GVW & Dump Truck Limits

Deliveries are capped by legal GVW and state DOT axle limits rather than bed volume alone:

  • Single-Axle Dump Truck: 5 to 6 tons (3.7 to 4.4 yd³ of #57) for tight drives.
  • Tandem-Axle Dump Truck: 12 to 14 tons (9 to 10.5 yd³) for residential lots.
  • Tri-Axle Dump Truck: 18.5 to 20 tons net (13.5 to 14.5 yd³ of #57, or 12 to 13 yd³ of crusher run).
  • End-Dump Tractor Trailer: 24 to 28 tons; requires wide turns and overhead wire clearance.

Subgrade Preparation, Geotextile Fabric & Drainage Slope

On soft subgrade soils, wheel loads push aggregate into clay while mud pumps into drainage voids. Crews prevent settlement with three steps:

  1. Match Geotextile Fabric: Use non-woven geotextile fabric (4-6 oz) for French drain filtration, and woven stabilization fabric under driveways on soft clay.
  2. Compact in 4-Inch Lifts: Run a 3,000-5,000 lbf plate compactor or heavy roller in 4-inch max lifts.
  3. Grade a 2% Cross-Slope: Pitch 1/4 inch per linear foot (2%) away from foundations so water drains instead of pooling.

Field & Quarry Ordering Notice

  • Call 811 Before Digging: Request utility locates 48-72 hours before trenching or excavation.
  • Scale Tickets & Geology: Weight runs 2,600-3,000 lbs/yd³ by limestone vs. granite geology and moisture; verify billed weight on quarry scale tickets.
  • Geotech & Inspector Review: Consult a geotechnical engineer or verify with your local building inspector on soft clay, frost heave, or heavy RV loads.
  • Driveway Permits: Confirm curb-cut setbacks and stormwater permeability rules with your local building department.

Frequently Asked Questions About Crushed Stone Yardage

How many tons of crushed stone are in a cubic yard? +
One cubic yard of #57 crushed limestone or granite weighs about 2,700 lbs (1.35 tons). Crusher run or dense graded aggregate (DGA) averages 2,900 to 3,000 lbs (1.45 to 1.50 tons) per cubic yard.
How many cubic yards of stone fit in a tri-axle dump truck? +
A tri-axle dump truck typically hauls 18.5 to 20 tons net payload within legal GVW and DOT axle limits, equal to about 13.5 to 14.5 cubic yards of #57 or 12 to 13 cubic yards of crusher run.
What is the difference between #57 stone and crusher run? +
#57 clean stone is washed to 3/16-inch (#4 sieve) to 1-inch angular pieces with ~40% void space for French drains. Crusher run blends 3/4-inch rock down to stone dust to lock into a structural base.
How thick should a crushed stone driveway base be? +
Passenger driveways over firm subgrade typically use 6 to 8 inches of compacted crusher run (21A/DGA) in 4-inch lifts, plus an optional 1.5- to 2-inch #57 top coat. Clay or RV pads need 10 to 12 inches.
Why add a compaction factor when ordering aggregate? +
Compactors with 3,000-5,000 lbf impact force consolidate loose rock. Clean #57 settles 5% to 8% as pieces reorient, while crusher run compacts 12% to 15% as fines fill voids so finished grade holds.
Materials & Masonry Calculators

Related Layout Tools

View Full Hardscape & Masonry Hub 10 Tools →