Five Layers of an Interlocking Paver System
Unlike poured concrete, interlocking concrete pavers transfer loads laterally into a compacted stone base. Rutting and edge spread occur when crews skimp on base thickness, lift compaction, or edge restraint. Build five layers:
- Native Subgrade: Strip topsoil, grade a 1.5%-2.0% slope away from structures, and compact until firm (jumping jack or trench roller on clay; plate compactor on sand).
- Geotextile Fabric: Roll 6-oz to 8-oz non-woven geotextile fabric (Class 1-2) with 12" overlaps to separate clay from aggregate.
- Dense Graded Aggregate Base: Compact 4"-6" crusher run (ASTM D2940) for patios, or 8"-12" for drives in 4" max lifts (2 lifts for 8", 3 lifts for 12").
- Bedding Sand Course: Screed a uniform 1.0" layer of washed concrete sand (ASTM C33) loose without pre-compacting.
- Pavers & Polymeric Sand: Set pavers, anchor edge restraint, and sweep dry polymeric sand into joints.
Sub-Base Material Specifications & Density Table
| Layer | Spec | Depth | Allowance | Density | Field Rule |
|---|---|---|---|---|---|
| Patio Base | Crusher Run (ASTM D2940) | 4"-6" | 15% Compaction | 1.50 T/yd³ | Compact in 4" max lifts |
| Drive Base | Crusher Run (ASTM D2940) | 8"-12" | 15% Compaction | 1.50 T/yd³ | Reversible plate compactor (5,000+ lbf centrifugal force) or trench roller |
| Bedding Sand | Washed Concrete Sand (ASTM C33) | 1.0" | 8% Screed & Seating | 1.35 T/yd³ | Screed over 1" pipes; never pre-compact |
| Joint Sand | Polymeric Sand | 1/8" Gap | Round Up | ~85 sq ft/bag | Blow pavers clean before misting |
The 6-Inch ICPI Overdig Rule
Digging to the exact finished patio size leaves border pavers unsupported. Per ICPI Tech Spec 2, extend compacted base stone at least 6 inches past the paver edge on all exposed sides (+12" to length and width). This overdig shoulder anchors 10-inch spiral spikes every 12"-18" in solid stone instead of soft soil.
How to Calculate Paver Base Depth & Sand: 5 Steps
Measure length and width in feet, then add a 6-inch perimeter overdig (12 inches total) so spike-anchored edge restraint sits on stone. Example 20x15 patio: 21 x 16 ft = 336 sq ft.
Sum compacted base depth (4" patio, 8" drive), 1.0" bedding sand, and paver thickness (2.375" for 60mm, 3.125" for 80mm). Default patio cut: 7.38 inches.
Multiply extended base area by depth in feet, divide by 27 for cubic yards, add 15% compaction allowance, and multiply by 1.50 tons/yd3 (336 sq ft x 0.333 ft / 27 x 1.15 = 4.77 yd3, or 7.16 tons).
Multiply paver area (excluding overdig) by sand depth in feet, divide by 27, add 8% screed and seating allowance, and multiply by 1.35 tons/yd3 (300 sq ft = 1.00 yd3, 1.35 tons bulk, or ~54 fifty-lb bags).
Divide paver square footage by 85 sq ft per 50-lb polymeric sand bag and round up (300 sq ft = 4 bags).
1-Inch Conduit Screeding Protocol
- Set Pipes: Space two 1" O.D. galvanized EMT conduits 6 to 8 ft apart on compacted stone.
- Screed Sand: Shovel damp ASTM C33 sand between pipes and pull a straightedge across for a flat 1.0" bed.
- Lay & Compact: Pull pipes, trowel-fill tracks, lay pavers from atop installed stones, lock restraints, and run a pad-equipped plate compactor over dry joints.
Contractor Field & Site-Safety Notice
- Call 811 First: Request utility locates 48-72 hours before digging, and hand-pot near private irrigation, pool, lighting, or septic lines.
- Scale Tickets & Moisture: Aggregate weight runs 1.35-1.65+ tons/yd³ by geology and moisture; verify billed weight on quarry scale tickets.
- Geotech & Inspector Review: Consult a geotechnical engineer or building inspector on expansive clay, frost heave, or heavy axle loads.
- Permits & Drainage: Confirm municipal impervious-cover permits and pitch subgrade 1.5%-2.0% away from structures.