Off Grid Solar Calculator
To calculate an off-grid solar system, divide daily Watt-Hours by the product of Peak Sun Hours and system efficiency (0.80) to determine required solar panel wattage. Multiply daily Watt-Hours by autonomy days and divide by usable Depth of Discharge to size the battery bank.
Off-Grid Energy Sizing Parameters
NREL Solar & NEC 690How to Engineer a Reliable Off-Grid Solar Power System
Building an off-grid solar installation that survives brutal winter conditions without blackouts requires a systematic 4-step engineering approach. Oversizing one component while under-sizing another creates bottlenecks that destroy batteries and waste solar harvest:
Accurately Audit Daily Watt-Hour Consumption
Never guess daily energy consumption. Use an electrical plug-in energy monitor (like a Kill-A-Watt) on refrigerators, Starlink satellite dishes, and laptops. For example, an Energy Star 12V DC compressor fridge uses ~450Wh/day, whereas an old 120V AC residential fridge can devour 2,000Wh/day. Factor in constant inverter standby idling (typically 25W × 24 hrs = 600Wh/day alone).
Design for Worst-Case Winter Peak Sun Hours
Summer sun is forgiving, providing 5.5 to 6.5 Peak Sun Hours across North America. However, winter brings short days and low solar angles, dropping solar irradiance down to 2.0 to 3.0 PSH in northern states. If your off-grid cabin is occupied year-round, size your solar PV array using December solar insolation figures to avoid running noisy backup generators continuously.
Select MPPT Over PWM Charge Controllers
Pulse Width Modulation (PWM) controllers clip solar module voltage down to battery voltage, discarding up to 35% of harvested solar energy. Maximum Power Point Tracking (MPPT) controllers actively track the voltage-current knee curve, converting surplus solar voltage into bonus charging current. MPPT is mandatory when wiring commercial 40V+ grid-tie solar panels into 12V or 24V battery systems.
Deploy 48V Architecture for Scalability
Pumping 3,000 Watts through a 12V battery system produces an enormous 250 Amps DC, requiring thick, rigid 4/0 AWG welding cables and dangerous thermal dissipation. Stepping up to 48V slashes continuous current to just 62.5 Amps, allowing flexible #4 AWG wire, cooler operation, and smaller, less expensive MPPT controllers.
Typical Off-Grid Appliance Daily Watt-Hour Benchmarks
| Appliance / Load | Average Running Watts | Typical Daily Runtime | Daily Energy (Wh) | Recommended System |
|---|---|---|---|---|
| Starlink Standard Dish | 55 Watts | 24 Hours (Continuous) | 1,320 Wh / Day | 24V or 48V Off-Grid |
| 12V DC Compressor Fridge (65L) | 45 Watts | 8 Hours (Duty Cycle) | 360 Wh / Day | 12V or 24V Camper/Cabin |
| 120V Residential Fridge (18 cu ft) | 120 Watts | 12 Hours (Duty Cycle) | 1,440 Wh / Day | 24V or 48V Homestead |
| 1/2 HP Submersible Well Pump | 900 Watts (2500W Surge) | 1 Hour (Intermittent) | 900 Wh / Day | 48V System with 3kW Inverter |
| LED Interior Lighting (6 Fixtures) | 50 Watts Total | 5 Hours | 250 Wh / Day | Any 12V/24V/48V System |
Off-Grid Solar System Sizing Frequently Asked Questions
How many solar panels do I need for an off-grid cabin? ▼
An average modest off-grid cabin consuming 3,500 Watt-Hours per day in an area with 4.5 Peak Sun Hours requires approximately 1,000 Watts of solar panels. Using modern 400-Watt monocrystalline panels, this requires 3 panels (1,200 Watts installed). If heating or air conditioning is added, daily consumption increases to 10,000+ Wh, requiring 8 to 12 panels.
How do I calculate days of autonomy for an off-grid battery bank? ▼
Days of autonomy represent how many consecutive sunless, overcast days your battery bank can power your cabin before reaching minimum cut-off voltage. Multiply daily Watt-Hours by autonomy days (standard is 2 days for residential cabins), then divide by battery usable Depth of Discharge (90% for Lithium, 50% for Lead-Acid) to determine minimum nominal battery bank capacity.
Should I build a 12V, 24V, or 48V off-grid solar system? ▼
For systems with under 1,000 Watts of solar, 12V is acceptable. For systems between 1,000W and 3,000W, 24V is strongly recommended to halve current and wire gauges. For whole-home systems above 3,000W of solar or using 3kW+ inverters, 48V is the universal trade standard, keeping DC currents low, preventing dangerous heat buildup, and cutting copper cable costs by 75%.
What size MPPT charge controller is required for my solar array? ▼
Divide total solar panel array wattage by your battery bank nominal voltage and multiply by 1.25 for NEC safety margins: Charge Controller Amps = (Total Solar Watts / Battery Volts) × 1.25. For example, a 1,200W solar array charging a 24V battery requires (1,200 / 24) × 1.25 = 62.5 Amps, necessitating a 60A or 80A MPPT controller.
Related Layout Tools
Solar Panel Tilt Angle Sizer
Fixed, winter, and summer solar tilt angles by latitude with roof pitch slope compensation.
Battery Runtime & Load Sizer
Runtime hours for LiFePO4, AGM, and Lead-Acid chemistries under depth of discharge.
Amp Hours to Watt Hours Tool
Convert battery capacity from Ah to Wh across 12V, 24V, 48V with cell schematics.
Watt Hours to Amp Hours Tool
Convert stored energy from Wh and kWh to required Amp-Hours for battery bank sizing.