How to Size and Cut a Bird's Mouth on a Rafter
A clean bird's mouth cut seats a sloped rafter onto the top wall plate so roof loads transfer straight into the framing. This birdsmouth cut calculator computes the rafter seat cut, vertical heel cut depth, plumb cut angle, and Height Above Plate (HAP) for gable roof framing and shed roof rafter builds.
Each bird's mouth pairs two 90-degree cuts: a horizontal seat cut bearing on the plate and a plumb heel cut along the wall line. On 2x6 rafter or 2x8 rafter stock, cutting too deep weakens the rafter tail, while cutting too shallow reduces plate bearing below code minimums.
Seat Cut Formula, Roof Pitch Angle, and HAP Geometry
All cut dimensions come from right-triangle geometry using pitch rise per 12 inches of run and plate width:
At 6/12 pitch on a 2x4 wall plate (3.5"), vertical heel cut depth is 1 3/4" (1 9/16" perpendicular). On a 2x6 wall plate (5.5"), vertical heel cut depth increases to 2 3/4".
IRC R802.7.1, R802.7.1.1 & R802.6 Rafter Notching Rules
Sawn lumber rafter notches must meet three code limits; verify local amendments with your building inspector before cutting:
- 1/4 Notch Limit (IRC R802.7.1 / R502.8.1): End notches cannot exceed 1/4 of actual rafter depth measured perpendicular to the rafter edge.
- Cantilevered Overhangs (IRC R802.7.1.1): Notched rafter tails with eave overhangs must keep at least 3-1/2" of uncut depth above the notch.
- Rafter Bearing Length (IRC R802.6): Provide at least 1.5" bearing on wood or steel framing, and 3" on masonry or concrete.
| Stock | Depth | Max 1/4 Perp. | 6/12 Heel Cut (3.5" Seat) | 6/12 Perp. | IRC R802.7.1 |
|---|---|---|---|---|---|
| 2x4 | 3.50" | 7/8" | 1 3/4" | 1 9/16" | Exceeds 1/4 & 3.5" Min |
| 2x6 | 5.50" | 1 3/8" | 1 3/4" | 1 9/16" | Exceeds 1/4 (Use 2x8) |
| 2x8 | 7.25" | 1 13/16" | 1 3/4" | 1 9/16" | Within Limit |
| 2x10 | 9.25" | 2 5/16" | 1 3/4" | 1 9/16" | Within Limit |
Framing Square & Speed Square Layout Steps
Framers lay out notches with a framing square and brass stair gauges or a 7-inch speed square:
- Mark the Plumb Line: Set stair gauges at pitch rise (tongue) and 12" (blade), then scribe the wall plumb line keeping the target HAP uncut.
- Scribe the Seat Line: Square 90 degrees off the plumb line with a speed square to mark your 2x4 or 2x6 wall plate bearing width.
- Mark the Eave Overhang: Measure past the heel line to your soffit width and strike a parallel fascia or sub-fascia cut on the rafter tail.
- Fasten for Wind Uplift: Where IRC R802.11 / Table R802.11 requires uplift ties, install a hurricane tie (e.g., H2.5A or H10A) with manufacturer-specified 1-1/2" connector nails or #9 SD screws.
Frequently Asked Questions About Bird's Mouth Cuts
What is the maximum depth allowed for a bird's mouth cut? ↓
Under IRC R802.7.1 and R502.8.1, rafter end notches cannot exceed 1/4 of the actual rafter depth measured perpendicular to the rafter edge: 1 3/8" max on a 2x6 rafter (5.5") and 1 13/16" max on a 2x8 rafter (7.25").
What is the minimum bearing length for a rafter on a top plate? ↓
IRC R802.6 requires at least 1.5 inches of bearing on wood or steel framing plates, and at least 3 inches on masonry or concrete.
What is HAP in roof framing? ↓
Height Above Plate (HAP) is the vertical distance along the plumb line from the notch corner to the top edge of the rafter. Uniform HAP keeps common rafters flat; hip and valley rafters require backing or a dropped HAP for their 45-degree diagonal run.
Can you cut a bird's mouth on an engineered I-joist or LVL rafter? ↓
No. Field-notching I-joist flanges is prohibited, and LVL rafters require engineer-approved sloped bearing details. Check the manufacturer's framing guide first.
Why shouldn't you overcut a bird's mouth with a circular saw? ↓
Over-cutting past the notch corner leaves a kerf that concentrates stress and can split the rafter tail under load. Stop the saw blade at the mark and finish with a handsaw.